Page 1 of 1

did i just CRASH my ECU on hdi 2.2?

Posted: Thu Jun 30, 2011 6:29 pm
by 406coupefan
Image
as u can see i get an seed key error. the line above says writing ok..

thats because i tryed to remap my car to default as the turbo didnt kick anymore after a short ecu test. anyways. when i tryed to flash it the wrong driver was installed due to pp2000 installation and the connection was made but as aparently not correctly. now my ecu shows the above data and wont let me flash anymore. it didnt work after 10 tries. i reset the computer disconnected the ecu galetto etc. but it wont le me upload my default settings anymore i cant upload .. read yes.. but thats it.. did i just break the ecu ? please tell me an solution :( :cry:

clearly btw the car wont start anymore...

well as i read it seems to be the face the ecu died? can anyone reprogramm it when i send it or something? :(

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Thu Jun 30, 2011 7:42 pm
by steve_earwig
Holy crap dude, that's a nightmare :( I've no idea what to do but perhaps you could ask over on the Ilexia forums http://www.ilexa.co.uk/forum/index.php?board=22.0 and/or ecu connections http://www.ecuconnections.com/

Good luck!

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Thu Jun 30, 2011 8:03 pm
by leehdi
Have you tried uploading the original file back up?

This is always the problem when using cloned tools

Do you have access to Peugeot Planet or some other diagnostic software to see if it will connect to the ECU?

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Thu Jun 30, 2011 9:55 pm
by Doggy
More hopefully, several of the coupe owners have experienced similar sounding problems, only to find the ecu responds correctly after being left alone for some time.

I have heard of other cases where, if the download process is interupted, the ecu becomes 'locked'. Possibly it can only be recovered by reprogramming by a specialist, off the vehicle.

Before you try that, I suggest the following, (may not help, but it will not make it worse).

1. Ensure your laptop / Galletto / drivers are now working correctly (and still do after shutting down and restarting your computer).

2. Turn off the ignition, remove the keys, close the doors and wait at least 15 minutes, before turning back on and trying again.

3. Follow the safe battery disconnection procedure here: viewtopic.php?f=10&t=13431

4. Leave battery disconnected fo at least an hour, before re-connectiong and trying again.

Hope that helps, let us know how you get on.

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Fri Jul 01, 2011 6:45 pm
by leehdi
ECU is only locked via IMMO

On a self learning ECU, if you d/c the battery for about 20-30mins it reverts back to default settings, so it might recover. Thats why if you leave your battery off for a while things like the idle is lumpy

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Mon Jul 04, 2011 3:02 pm
by 406coupefan
@leehdi yea i tryed atually thats what im trying right now.. got backup files.. and the programm worked fine as i said tuned the engine half a year ago like that worked fine for me.. just me stupid was trying it again and it crashed due to wrong drivers.. so my fault..

anyways @all thanks for the help but it didnt work i cant reset the ecu it wont work with battery off for days...still shows me key symbol n wont start.. its dead..
so i tryed the local tuners theyll fix it for like 300€ around here....
so i just ordered today a used ecu,bsi and key fob to work properly for around 200€ includ. shipping.. i hope changing them will work than again.. but im quite sure like that problem is solved anyone care for a broken ecu!?

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Sun Jul 10, 2011 6:29 pm
by leehdi
You can reprogram it using the boot mode and your galletto

Image

Image

Image

On a galletto k-line is pin 7, earth is pin5 and +12V is pin16

Re: did i just CRASH my ECU on hdi 2.2?

Posted: Thu Jul 14, 2011 2:41 pm
by leehdi
As requested

Image