I did say all the above, in other words Phillip read though all the postsPhillipM wrote: ↑Sun Jan 13, 2019 5:39 pm Gas mig.
Gasless is a pain in the arse as it starts much worse than gasless and you'll have to do more cleanup, TIG is a waste of time unless you cut it back to completely perfectly clean metal and get your repair seamless - and you have it indoors otherwise the wind is a nightmare.
Stick welder? Forget it on car bodywork. It can be done, yes, but it always ends up a hell of a mess to sort out.
B
Beware that slapping a patch over the top usually just means the rest of it will rust even faster as you've created a moisture trap. So if you're keeping the car, worth doing it right the first time.
going to have a go at welding the sills !
Moderator: Moderators
-
- 3.0 24v
- Posts: 1521
- Joined: Sun Apr 28, 2013 11:02 pm
- Location: Coalville, Leics.
Re: going to have a go at welding the sills !
2002 110 HDi estate, Rapier in monaco blue! ( found quite a bit more power ) SOLD I've sorted the airbag light
1998 3.0 V6 SE coupe in Diablo Red ( my baby ) sold
2006 206 1.4 16v sport in Aegean blue ( wife's shopping trolley )
2006 BMW e61 535d m-sport run's for cover
1998 3.0 V6 SE coupe in Diablo Red ( my baby ) sold
2006 206 1.4 16v sport in Aegean blue ( wife's shopping trolley )
2006 BMW e61 535d m-sport run's for cover
-
- 2.0 16v
- Posts: 151
- Joined: Sun Mar 11, 2018 4:00 pm
- Location: Cumbria
Re: going to have a go at welding the sills !
There does come a point where its just not worth it to keep throwing money at it. It was the same with my calibra, mechanically it was perfect but bodywise it was a nightmare. I changed both front wings the tailgate a door one of the sills drivers side floor pan, it was just one thing after another. Took it for its next mot and the tester called me over and stuck his finger through the passengers side floor in a few places, by this time one of the front wings had started going again. As much as I loved it, I had to let it go i just couldn't afford to keep replacing metal.
1984 924 2.0 n/a crystal Green - The daily
2005 VW Passat tdi 130 Highline, now 170bhp & 290ft/lb
2000 Peugeot 406 2.0 hdi - stood for 4 years, fresh mot and mostly working.
2005 VW Passat tdi 130 Highline, now 170bhp & 290ft/lb
2000 Peugeot 406 2.0 hdi - stood for 4 years, fresh mot and mostly working.
Re: going to have a go at welding the sills !
Thanks for your input guys
If it goes through the MOT without to much trouble will keep for a few more years as long as the clutch 175k holds out, apart from the sills car is still in good nick
Hope it does not need to many patches on the sills ???
If it goes through the MOT without to much trouble will keep for a few more years as long as the clutch 175k holds out, apart from the sills car is still in good nick
Hope it does not need to many patches on the sills ???
Re: going to have a go at welding the sills !
RESULT:
Put the car in for its MOT today and cannot believe it the sills passed and it only needed the wheel bearing which I knew about
Put the car in for its MOT today and cannot believe it the sills passed and it only needed the wheel bearing which I knew about
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: going to have a go at welding the sills !
That is indeed a bit of a result, the rust can't be near enough to anything structural (although I'd have a thought the whole sill is structural... )
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
-
- 3.0 24v
- Posts: 3575
- Joined: Fri Apr 06, 2012 9:02 pm
- Location: Bournemouth
Re: going to have a go at welding the sills !
Excellent - this gives you a 11 months to procrastinate over a fix
2003 2.2hdi estate - mine
1998 Volvo 940 auto estate - also mine
2019 Citroen C3 something - the wife's
PP2000 user, can help with faults / diagnostics in the Bournemouth area.
1998 Volvo 940 auto estate - also mine
2019 Citroen C3 something - the wife's
PP2000 user, can help with faults / diagnostics in the Bournemouth area.
-
- 3.0 24v
- Posts: 1521
- Joined: Sun Apr 28, 2013 11:02 pm
- Location: Coalville, Leics.
Re: going to have a go at welding the sills !
result
I did say earlier on in this post that the reg's changed a few years back, you can have no outer sills
& it'll still pass as long as it's more than 150mm from a suspension mounting point
I did say earlier on in this post that the reg's changed a few years back, you can have no outer sills
& it'll still pass as long as it's more than 150mm from a suspension mounting point
2002 110 HDi estate, Rapier in monaco blue! ( found quite a bit more power ) SOLD I've sorted the airbag light
1998 3.0 V6 SE coupe in Diablo Red ( my baby ) sold
2006 206 1.4 16v sport in Aegean blue ( wife's shopping trolley )
2006 BMW e61 535d m-sport run's for cover
1998 3.0 V6 SE coupe in Diablo Red ( my baby ) sold
2006 206 1.4 16v sport in Aegean blue ( wife's shopping trolley )
2006 BMW e61 535d m-sport run's for cover