long shot 1.6 hdi 207/307 110bhp pinouts

[leehdi]

It will be that one then as I know like the 29f040 for example has some numbers after it.

The flash file is when you desolder the eeprom and plug it into a programmer

[adaptorman]

It will be that one then as I know like the 29f040 for example has some numbers after it.

The flash file is when you desolder the eeprom and plug it into a programmer

so ive defo got the right chip off the board lee, regards emmprom programer ,any idea what flash file type i need?

and do you possibly know what all the ecu bocsh numbers mean ie 0281 ...012...465 ,most ecus start with 0281 ,, but the other 2 sets of numbers are differnernt evern thow they off the same car,engine spec ?

so i need so emmprom flash next ?

[leehdi]

You'll read the file and save it in either .ori or .bin

The kit will cost you in excess of £200. Cos you need a programmer, possible a pic adapter and a hot air station

They are just a bosch part number

[adaptorman]

You'll read the file and save it in either .ori or .bin

The kit will cost you in excess of £200. Cos you need a programmer, possible a pic adapter and a hot air station

They are just a bosch part number

ive got a few emmprom flashers here hee, which i mostly used for obd1/2 vws but im assumeing i need a differnert type/version ,do these come with the software to flash , if not were best place to buy it , ps ive managed to read th oringal bin file off the ecu and removed dpf , but carnt the immobilzer as yet , as my first plan was to swop it from one ecu to another ,as id personaly pref to refit the immobilzer code ,yet now ive also been advise that with the battery disconected the bsi control unit will have also lost its memory (stress if its not one thing its another buggar lol)and i dont have a key card regards recodeing the bsi , so question is , say i tempory keep the new ecu and leave immo off should the vechical still start?

[adaptorman]

hi lee tryed to read the immo chip today useing a william emprom selected all the correct information , but wouldnt read the chip just came back with a load of (ffffffffff) hernce wouldnt read the info , dam thing as ive got all the correct files, immo bin file etc , unless its the chip whats corrupt ?

[leehdi]

It's all F's?

Can't you remove the immo coding for the time being and run the car with no immo until you can sort the coding?

[adaptorman]

It's all F's?

Can't you remove the immo coding for the time being and run the car with no immo until you can sort the coding?

how do i do that lee , as i carnt just remove the immo chip ,as it contects and states its read the chip yet theres nothing in the file ,tests/checks and settings are correct from the manual,im woundering if the chip is corroupt,herance why i carnt read whats on it,otherwise i would have posted a pic up ps what software ,programer is recomended as i personaly dont think this ones up to the job tbh, ps lee i notice your local too

[leehdi]

I'm only just learning myself mate with regards to coding, and only know the odd bit.

I get one of my mates to do it normally, with regards to having a free running ECU

If you email me your dump, along with the full eeprom number and ECU number, I'll see if I can get the code edited for you

[adaptorman]

this is the issiuse lee as i carnt read the chip to get any infomation from it? i have the the correct immo delete bin and bin file, i know which part needs editing, if u can let me know whitch programer type/model i need i can give it another go ,

[adaptorman]

hi all just a quicky ecu arrived today , good news engine starts/runs, but i now have another (esp faulty)?any ideas clues as i know it didnt have this fault before

[leehdi]

I'm buying this one - http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... K:MEWAX:IT

You might have to recode your COM2000 steering angle sensor

[adaptorman]

i have the same programer witch wont read the chip ,removed off the board , ill try a system reset off the bsi unit first may help?(worth a try before more techical stress lol)

[leehdi]

It's all fun and games

[steve_earwig]

'it it wi' 'ammer

Any joy with the ESP?

[adaptorman]

no joy on esp as yet,as i thought it was ecu codeing, so ive read my oringal ecu and code and writern it to my new ecu , which worked fine , but the esp fault is still there, just removing dpf from the ecu , then ill try to found out the esp fault , maybe abs unit with battery short/possible bsi codeing or steering codeing , ill plug the fault coder back in to see what things it shows ,(ill take some pics ps found some decent software to read,write to the ecu