and today i have mostly been...
Moderator: Moderators
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
...wondering where all the bluddy time's going
Surprise!
I think Miloš was. Reassembled on the dining room table last night (you can tell t'wife's not here ) and tested this morning, mostly by Miloš as I have a pathological fear of chainsaws (thanks dad )
I'm thinking this was the culprit
The fuel line that goes from the tank to the carb, there's a split just below the gromet. The primer is on the other side (it's the sort that pulls fuel through the carb, rather than chucking fuel into the choke), there's a little diaphragm pump in the bottom of the carb that sucks fuel through this tube from the tank and I reckon it was also pulling air through the split. Hopefully that's it done, it's run ok before while I've been a-fiddling but I think this time it's fixed. Miloš was well pleased. Total cost: about the same as UK, about 4 quid (maybe it's only me the shop rips off )
Ok, that's 15 minutes gone, what's next? Ah crap, cook lunch, go shopping. maybe I do miss t'wife
Surprise!
I think Miloš was. Reassembled on the dining room table last night (you can tell t'wife's not here ) and tested this morning, mostly by Miloš as I have a pathological fear of chainsaws (thanks dad )
I'm thinking this was the culprit
The fuel line that goes from the tank to the carb, there's a split just below the gromet. The primer is on the other side (it's the sort that pulls fuel through the carb, rather than chucking fuel into the choke), there's a little diaphragm pump in the bottom of the carb that sucks fuel through this tube from the tank and I reckon it was also pulling air through the split. Hopefully that's it done, it's run ok before while I've been a-fiddling but I think this time it's fixed. Miloš was well pleased. Total cost: about the same as UK, about 4 quid (maybe it's only me the shop rips off )
Ok, that's 15 minutes gone, what's next? Ah crap, cook lunch, go shopping. maybe I do miss t'wife
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
And this evening I shall be basking in the absolute silence of the Croatian football team's defeat at the World Corruption Final. Woo.
Seriously, all afternoon the apes have been getting louder, awful music, fireworks, air raid sirens, fire engine sirens, car horns, drunken bellowing, reaching a crescendo about 20 minutes ago, the animals have been nervously rushing about, I've had all the windows shuttered so it's pretty hot in here and suddenly...
SILENCE
I am overjoyed Croatia lost, I couldn't give a flying sock who won.
Seriously, all afternoon the apes have been getting louder, awful music, fireworks, air raid sirens, fire engine sirens, car horns, drunken bellowing, reaching a crescendo about 20 minutes ago, the animals have been nervously rushing about, I've had all the windows shuttered so it's pretty hot in here and suddenly...
SILENCE
I am overjoyed Croatia lost, I couldn't give a flying sock who won.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- Welly
- The moderator formally known as Welton
- Posts: 15033
- Joined: Tue Jan 10, 2006 12:52 pm
- Location: East Midlandfordshire
Re: and today i have mostly been...
I'm with you on the football, I mean can we just get back to normal now we know we're rubbish at it.
Cars in my care:
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
I can't even see why anyone takes it seriously any more, after all the allegations about corruption, fraud, tax fiddling and match fixing we've heard about over the past few years. It wouldn't surprise me if the winner was decided in a brothel somewhere in the middle of Europe last year, England weren't going to win it because of Brexit but Croatia stood a chance as the EU's latest slave market, you gotta keep the drones happy. Hey, I think I saw something about some strange referee decisions, I guess that's when the players forget their instructions and start playing for real.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- Welly
- The moderator formally known as Welton
- Posts: 15033
- Joined: Tue Jan 10, 2006 12:52 pm
- Location: East Midlandfordshire
Re: and today i have mostly been...
Well yesterday, I was at Welly_Junior's Graduation Ceremony at Warwick University, he got a First Class Honors Degree in German Studies
Cars in my care:
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
Yay! Conhratulations Welly_Jnr.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- Doggy
- Mod with a 2.2 HDi, De-Fapped!
- Posts: 10710
- Joined: Mon Oct 13, 2008 11:49 pm
- Location: Northants
Re: and today i have mostly been...
Well done Welly_Jnr!
2002 HDi 2.2 Exec Estate, (2008-12) (wonderful)
2003 HDi 2.2 6-speed Exec Estate (2012-19) (also a gem)
2009 Citroen C5 2.0 HDi VTR+ Estate (godawful heap)
2008 BMW E91 330i touring (great fun - murdered by a reversing SUV)
2007 BMW E91 325i touring (slower smoother quieter)
2003 HDi 2.2 6-speed Exec Estate (2012-19) (also a gem)
2009 Citroen C5 2.0 HDi VTR+ Estate (godawful heap)
2008 BMW E91 330i touring (great fun - murdered by a reversing SUV)
2007 BMW E91 325i touring (slower smoother quieter)
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
I have a tin roof They started yesterday putting the battens up and today they got most of the tin up.
Yes, there's a gutter. Only on one side though,the other side is below that hazelnut and I'd have no way of clearing the leaves out of it (without getting a knife stuck in my back...)
To me, to you...
As it stands
Tomorrow they've got to fit the rest of the snow catchers and finish the ridge and then it's, well, done
Meanwhile, I've been playing with that door.
There was a lot of too-ing and fro-ing with the laths to get the right width (had to make up over an inch) but I got there in the end. I also cut the top 2cm off it, as little as I could to get back to (mostly) solid wood.
I also pulled the frame
Milop and his misses were hear earlier (t'wife came back from GB last night and they wanted to see her before they go on their holidays tomorrow) and Miloš gave me a hand moving the frame - it really is oak! And then he had the idea of sticking it in the hole.
Bleedin' 'eck, it fits!The frame's a bit rotten at the bottom but it's below the door, Miloš says anything below the bottom of the door can be chopped off anyway.
Yes, there's a gutter. Only on one side though,the other side is below that hazelnut and I'd have no way of clearing the leaves out of it (without getting a knife stuck in my back...)
To me, to you...
As it stands
Tomorrow they've got to fit the rest of the snow catchers and finish the ridge and then it's, well, done
Meanwhile, I've been playing with that door.
There was a lot of too-ing and fro-ing with the laths to get the right width (had to make up over an inch) but I got there in the end. I also cut the top 2cm off it, as little as I could to get back to (mostly) solid wood.
I also pulled the frame
Milop and his misses were hear earlier (t'wife came back from GB last night and they wanted to see her before they go on their holidays tomorrow) and Miloš gave me a hand moving the frame - it really is oak! And then he had the idea of sticking it in the hole.
Bleedin' 'eck, it fits!The frame's a bit rotten at the bottom but it's below the door, Miloš says anything below the bottom of the door can be chopped off anyway.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
-
- 2.0 16v
- Posts: 151
- Joined: Sun Mar 11, 2018 4:00 pm
- Location: Cumbria
Re: and today i have mostly been...
Taking the passat for its mot, which thankfully it passed with flying colours.
1984 924 2.0 n/a crystal Green - The daily
2005 VW Passat tdi 130 Highline, now 170bhp & 290ft/lb
2000 Peugeot 406 2.0 hdi - stood for 4 years, fresh mot and mostly working.
2005 VW Passat tdi 130 Highline, now 170bhp & 290ft/lb
2000 Peugeot 406 2.0 hdi - stood for 4 years, fresh mot and mostly working.
- Welly
- The moderator formally known as Welton
- Posts: 15033
- Joined: Tue Jan 10, 2006 12:52 pm
- Location: East Midlandfordshire
Re: and today i have mostly been...
Your mansh....outbuilding looks beautiful, seriously
Cars in my care:
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
Thankyew It is starting to look a hell of a lot better.
The roofers returned, they were here a whole 20 minutes and... it's done!
Errr, why did they finish with half a snow deflector? Couldn't they have just... Ah well, I guess that's the way it's done.
The roofers returned, they were here a whole 20 minutes and... it's done!
Errr, why did they finish with half a snow deflector? Couldn't they have just... Ah well, I guess that's the way it's done.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- Welly
- The moderator formally known as Welton
- Posts: 15033
- Joined: Tue Jan 10, 2006 12:52 pm
- Location: East Midlandfordshire
Re: and today i have mostly been...
Snow?
It doesn't snow that much there does it?
It doesn't snow that much there does it?
Cars in my care:
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
They tell me there was more once. Quite a few years back my friend Vesna had enough snow slide off her roof to flatten her car So yeah, snow deflectors. It actually slides off the solar panels here with enough speed to clear the terrace and leave a heap all the way along the railings.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- steve_earwig
- Moderator
- Posts: 19811
- Joined: Thu Oct 04, 2007 6:09 pm
- Location: Jastrebarsko, Croatia http://www.jastrebarsko.hr/lokacija/
Re: and today i have mostly been...
My angle grinder's packed up It's actually loosing an bearing so may be repairable. This would be the cheap 'n' cheerful one I bought from the supermarket here for about 20 quid after the Bosch I'd had for about 20 years was flipped out of my hands and self-destructed on the floor when I was sanding beams in the loft. The last cheapy I bought only lasted a month before it basically exploded in my hands but I thought if it lasted long enough to finish the loft I'd have had more than my money's worth. 2 years later it's survived all sorts of abuse, all I've done is put some proper angle drive grease in the head. Is it time to buy a proper one? Nah, new bearing it is.
Unskilled meddling sin©e 2007
The submitted form was invalid. Try submitting again.
The submitted form was invalid. Try submitting again.
- Welly
- The moderator formally known as Welton
- Posts: 15033
- Joined: Tue Jan 10, 2006 12:52 pm
- Location: East Midlandfordshire
Re: and today i have mostly been...
Please be careful with cheap power tools, if you're lucky they'll just stop working, if you're not they'll injure you.
Can you get Ryobi stuff there? everyone's going crazy for there stuff in the construction industry here.
Can you get Ryobi stuff there? everyone's going crazy for there stuff in the construction industry here.
Cars in my care:
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work
2021 Kia Spottage 1.6 Pez Turbo Dual Clutch Gearbox Trickery
2013 Renner Twingo - donkey work